EverythingOutboards / 1960s Service Bulletins

Johnson Service Bulletin SB-1064 (1965)

This 18-page factory booklet documents ignition coil and condenser identification, recommended applications, and test specifications for Johnson outboard motors. The cover, technical drawings, charts, and back cover are preserved as historical page reproductions; the first three numbered pages are transcribed for searching.

Original Johnson SB-1064 coil and condenser booklet front cover
PAGE 1   SERVICE BULLETIN SB-1064
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60086
September, 1965 SUBJECT: COILS AND CONDENSERS; IDENTIFICATION CHARTS, USAGE CHARTS, AND TEST SPECIFICATIONS, ON ENGINES: ALL 1951 THRU 1966 JOHNSON OUTBOARD MOTORS With coils that look as much alike as our 580118, 580416, and 580197 coils, it is quite possible that a mechanic might inadver- tently install the wrong one of them in a particular engine. Fur- thermore, once an incorrect coil has been installed in an engine, it is quite easily passed off as a "bad coil" the next time that the engine is tuned-up, simply because it doesn't check out with the specifications given for the coil that is supposed to be in the particular model motor being worked on. Although the parts catalogs provide a method of determining which coil should be used in each model engine, we believe that you should have some simple and rapid way of identifying the various coils and condensers that we use and that are in service, Then if a motor comes to you for service with the wrong coil in it, you will be able to spot the discrepancy immediately. We believe that the following explanation and the enclosed identification charts, usage charts and test specifications for both coils and condensers, will help in this matter. Identification - Coils The color of the plastic insulation that is used on our 2-cycle magneto coils can serve as a rapid means of identifying or dis- tinguishing between them. For example: The plastic insulation on Coil 580118 is purple (transparent or opaque). The plastic insulation on Coil 580197 is light blue. The plastic insulation on Coil 580416 is purple. The plastic insulation on 580416 coils used in 3 HP engines made in Belgium is green (transparent).
PAGE 2   SERVICE BULLETIN SB-1064
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60086
An alternate, and possibly a more accurate method of identifying these coils, is by the thickness of their lamination assembly. The thickness of the lamination assembly in Coil 580118 is approx. 27/64". The thickness of the lamination assembly in Coil 580197 is approx. 15/32". The thickness of the lamination assembly in Coil 580416 is approx. 27/64". COILS 580118 & 580416 You will note that Coils 580118 and 580416 are of similar color. These two coils also have identical test characteristics, as can be seen from comparing the values given for them on the enclosed sheets of test speci- fications. Coil 580118 has been superseded by Coil 580416, as indicated in your Master Parts Price List. Although Coil 580416 is designed to work every place that Coil 580118 had previously been used, Coil 580118 can not be used in applications specifically calling for use of Coil 580416. COIL 580197 Coil 580197 can be easily distinguished from Coil 580118 and Coil 580416 by its lamination assembly which is approximately 15/32 inches thick. This difference in the thickness of the lamination assemblies is readily noted in the enclosed identification charts. COIL 378231 On engines in service using Coil 378231, an Autolite, a Prestolite, or YU a Delco-Remy Coil may be found, as all three of them were used in pro- duction. These Coils are easily identified, as shown on the enclosed identification charts. Test specifications for each of these Autolite or Prestolite Coils and for the Delco-Remy Coil are found in the enclosed sheets of Coil Test Specifications, The rest of the coils are easily identified from the enclosed charts. Therefore, nothing further need be said about them. Identification - Condensers A Condenser Identification Chart, with a view of each condenser and its respective capacitance in Microfarads, is also enclosed. Although the condensers are not shown in actual size, the views shown have all been reduced the same amount so that a comparison of their relative sizes is maintained, CONDENSER 510173 Condenser 510173 is no longer a serviced part and is therefore shown in the current issue of the Master Parts Price List as being super- seded by Condenser 580321. Condenser 510173 is still being used on some production engines. You will note that the capacitance of the 510173 Condenser and the 580321 Condenser are identical. This is true, because except for physical size these two condensers have identical characteristics, The capacity of each of these condensers is .18-.22 Microfarads.
PAGE 3   SERVICE BULLETIN SB-1064
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60086
CONDENSER 580321 Condenser 580321 is used for servicing engines of under 18 H.P. Condenser 580422 can not and should not be used in place of Condenser 580321 because the greater capacity of Condenser 580422 would permit excessive build-up on the breaker points if used in the smaller engines. Therefore, to obtain maximum breaker point life, only Condenser 580321 should be used when servicing engines of less than 18 H.P. Condenser 580321 has a capacity of .18-.22 Microfarads. CONDENSER 580422 This condenser has been specially designed with a capacity of .25 to .29 Microfarads, and for this reason MUST be used ONLY in 18, 30, 35 and 40 horsepower engines. As a visual means to aid in identification, note that Condenser 580422 is one-eighth (1/8) inch higher than Con- denser 580321. Condenser 580422 was designed to eliminate a field-reported miss in the intermediate to high RPM range on 18, 30, 35, and 40 horsepower engines. Therefore, whenever there is an indication of a miss on any of these engines (sometimes described as full throttle RPM fluctuation), remove the 580321 Condensers and replace them with the 580422 Condensers, It is recommended that 580422 Condensers be installed on all 18, 30, 35 and 40 horsepower engines whenever they are brought in for service to insure against the possibility of a miss developing at a later time. Condenser 580422 is available from your Parts Distributor at the Suggested List Price of $1.00 each and is subject to the standard parts discount. Do not rely on what some other mechanic has inadvertently put in an engine that is now in your shop. A mistake can cost you your repu- tation, and his error may be the reason for the motor currently needing service. It is hoped that with the enclosed information, you will be able to more rapidly complete repairs on engines that come to you for service. JOHNSON MOTORS N. Peter Hansen Administrative Assistant NPH:rs
SB-1064 original factory page 4: coil and condenser identification illustrations
SB-1064 original factory page 5: coil and condenser identification illustrations
SB-1064 original factory page 6: coil and condenser identification illustrations
SB-1064 original factory page 7: coil and condenser identification illustrations
SB-1064 original factory page 8: recommended coil and condenser usage chart
SB-1064 original factory page 9: recommended coil and condenser usage chart
SB-1064 original factory page 10: recommended coil and condenser usage chart
SB-1064 original factory page 11: recommended coil and condenser usage chart
SB-1064 original factory page 12: coil test specifications
SB-1064 original factory page 13: coil test specifications
SB-1064 original factory page 14: coil test specifications
SB-1064 original factory page 15: coil test specifications
SB-1064 original factory page 16: coil test specifications
Original SB-1064 booklet back cover

Coil and condenser part-number reference

This searchable index identifies part numbers printed in the booklet. Descriptions are limited to what the factory pages support. For model compatibility and test values, consult the original usage and specification charts above.

Part numberIdentification / description
375189Ignition coil
378231Ignition coil (Autolite, Prestolite, or Delco-Remy)
379569Ignition coil
580118Ignition coil (superseded by 580416)
580197Ignition coil (light-blue insulation)
580243Ignition coil
580416Ignition coil (purple insulation; Belgian 3 HP version green)
300153Condenser
510173Condenser (superseded by 580321)
580256Condenser
580321Condenser (.18-.22 microfarads; under 18 HP)
580422Condenser (.25-.29 microfarads; 18, 30, 35 and 40 HP)
200668Alternative ignition coil (Autolite/Prestolite)
200669Alternative ignition coil (Autolite/Prestolite)
200670Alternative ignition coil (Autolite/Prestolite)
915080Alternative ignition coil (Autolite/Prestolite)
1115153Alternative ignition coil (Delco-Remy)

Factory charts are preserved as images. This index does not replace the original application and test tables.