Back to Service Bulletin Index

Johnson Service Bulletin SB-1078 - Test Wheels (1966)

Issued December 1965 for all 1966 Johnson engines, this three-page factory bulletin lists the test wheels used for tank testing, the minimum recommended wide-open-throttle RPM for each model, and original dealer-net prices. It also includes the original parts-depot order blank. Test wheel 311733 is specified for the 5 HP LD(L)-11; 381283 is listed for the 100 HP V4ML-12.

Johnson Motors Service Bulletin factory letterhead

SB-#1078

December, 1965

SUBJECT:   TEST WHEELS

ON MODELS: ALL 1966 ENGINES

Below are listed the test wheels that are recommended for use when tank testing the various models of the 1966 Johnson line of Outboard Motors. Also listed are the recommended desired minimum RPM that each respective engine should develop when run at wide open throttle with the correct test wheel installed. Please note that the price of each test wheel is included in the list and that test wheels that are new for 1966 are shown in bold type.

MODELH.P.MINIMUM RPMTEST WHEEL
PART NUMBER
NET PRICE
CD(L)-2364000380757$2.50
FD(L)-20204450376913$3.40
JH(L)-2133850310765$2.40
JW(L)-2133850203229$1.35
LD(L)-1154150311733$2.40
MQ(L)-129.54400379673$3.80
RD(L)-28404300378566$5.00
RDS(L)-28404300378566$5.00
RK(L)-28404300378566$5.00
RX(E)(L)-14334400377014$4.50
**V4A(L)-18804700379215$4.70

PAGE 2   SERVICE BULLETIN SB-#1078

JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60086

MODELH.P.MINIMUM RPMTEST WHEEL
PART NUMBER
NET PRICE
**V4ML-121004450381283$13.50
**V4S(L)-18804700379215$4.70
**VX(L)-12604250379215$4.70
**VXH(L)-12605200*377400$6.90

All of the above listed test wheels are available from:

OMC Parts Depot
Galesburg, Illinois

Please be sure to include Prepayment when ordering items from the Parts Depot. An order blank is enclosed with this bulletin to facilitate ordering test wheels.

JOHNSON MOTORS

N. Peter Hansen
Administrative Assistant

NPH:rs

*Minimum RPM - Do not exceed 5000 RPM for more than 10 seconds. Engine must not be operated in excess of 5000 RPM when operated on a boat.

**When running these engines in a test tank, a supplemental water supply should be introduced through the water by-pass cover plate located on the port side of the lower unit. The pressure of such a water supply should not exceed 10 p.s.i. Refer to your Special Tool Catalog for the adapters necessary to accomplish this.

NOTE: Post on your Miscellaneous Index under the heading "Tools".

ORDER

TO: OMC PARTS DEPOT
    Galesburg, Illinois

Model UsageHPTest Wheel
Part Number
Net Unit PriceQuantityExtension
CD(L)-2363807572.50________________
FD(L)-20203769133.40________________
JH(L)-2133107652.40________________
JW(L)-2132032291.35________________
LD(L)-1153117332.40________________
MQ(L)-129.53796733.80________________
RD(L)-28403785665.00________________
RDS(L)-28403785665.00________________
RK(L)-28403785665.00________________
RX(E)(L)-14333770144.50________________
**V4A(L)-18803792154.70________________
**V4ML-1210038128313.50________________
**V4S(L)-18803792154.70________________
**VX(L)-12603792154.70________________
**VXH(L)-12603774006.90________________

Sub Total __________
Illinois Dealers Add 4% Sales Tax __________
Total __________

SEND ORDER TO: Outboard Marine Corporation, Galesburg, Illinois.

Full remittance must accompany order - No C.O.D. Shipments. Make check or money order payable to: Outboard Marine Corporation. All prices are net F.O.B. destination and are subject to change without notice.

Ship above items to: NAME __________________________

ADDRESS ______________________________

CITY/STATE ____________________________

SIGNED ________________________________