Johnson Service Bulletin SB-1143

Starter Drives #377304 and #378228 - August 1967. Johnson Motors described improvements to V4 starter drives, specified replacement hardware and cautioned against interchanging the two assemblies.

Johnson Motors Service Bulletin gray factory letterhead
August, 1967 SB-#1143

SUBJECT:  STARTER DRIVES #377304 AND #378228

ON MODELS:
V4S-10S thru - 50, 75 & 80 H.P.
VX-10S thru - 60 H.P.
VXH-10S thru - 60 H.P. Heavy Duty
V4H-16A thru 18C - 75 H.P.
V4A-19R thru - 80 H.P.
V4T-13A thru - 100 H.P.
GT-10S - 115 H.P.






#377304

V4A-13 thru 18C - 75 & 80 H.P.
V4M-10S thru 11C - 90 H.P.
V4ML-12R & 12M - 100 H.P.
#378228

We have recently made several improvements in these starter drive assemblies. These changes went into effect in two stages on late 1967 engines.

The first change removed #204378 Spacer-cushion from the drive assembly and changed the Screw-Starter Housing to Crankcase, from 1-#553556 (1/4-20 x 13/16 sems) to 1-#302479 (5/16-18 x 1-1/8 hex head capscrew) and 1-#306325 (5/16 split lockwasher). See Fig. 1.

The second change modified the gear on #378178 Gear and Shaft Assembly, identifiable by the large chamfer on the lower side of this gear (Fig. 2) and provided a longer cushion #204381. To get this improvement into effect as rapidly as possible, a 1/16" thick rubber washer was used with the original cushion until the longer cushions were available.

When servicing any V-4 starter drive, the following procedure is recommended:

1.Discard #204378 Spacer-cushion.
2.The #204381 Cushion should be at least 3/4" long. Discard any part that is shorter. The 1/16" thick rubber washer used in some production drives will not be serviced separately. Parts currently being supplied from Depot have the 3/4" minimum length.
3.Do not reuse #307396 Nut-bendix drive. Use a new nut and torque it to 20-25 ft. lbs.
4.Inspect the starter drive housing carefully, particularly where it pilots on the crankcase and replace it if it is
PAGE 2      SERVICE BULLETIN SB-1143
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
Figure 1: starter housing and exploded starter drive, showing mounting screws and spacer
Figure 1
Figure 2: exploded starter drive, rubber washer and full chamfer
Figure 2
PAGE 3      SERVICE BULLETIN SB-1143
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085

cracked or bent, using service assembly #382959 which supersedes #378178 Housing. This assembly uses the housing drilled for the 5/16" bolt used in production along with 1-#306418 Screw (1/4-20 x 1-1/8), 1-#306369 Lockwasher and 1-#313079 Flat Washer.

The above screw and washers, torqued to 9-11 ft. lbs., should be used in place of existing Screw #553556 on early engines. The 5/16" Screw used on late engines should be torqued to 10-12 ft. lbs.

5.Alternately tighten the starter thru bolts and the screw-starter support to crankcase - just snug to correctly position the starter motor and support bracket before torquing these bolts.
6.Make sure the engine is tuned properly and that the owner is following correct starting procedures as given in the owner's manual. Particularly caution against engaging the starter when the flywheel is moving.

The only difference between the two subject Starter Drive Assemblies is the drive pinion which prevents interchangeability (Fig. 3). Their correct usage is outlined at the beginning of this bulletin.

Since it is entirely possible to accidentally install either assembly on the wrong engine, the following results can be expected:

1.If #377304 is installed in place of #378228, the short tooth drive pinion will not engage the flywheel ring gear, but lift against the underside of the flywheel with considerable pressure, possibly causing internal engine damage.
Figure 3: comparison of starter drive assemblies 377304 and 378228
Figure 3
2.If #378228 is installed in place of #377304, the long tooth drive pinion will engage but not completely disengage once the engine starts. This would result in starter motor damage.
JOHNSON MOTORS

Carl Klawonn
Administrative Assistant

CK/rkm

Related service information

SB-936 (January 13, 1963) - earlier bulletin expressly superseded by SB-1143. The factory instructed dealers to destroy the previous issue.

Original starter drive applications: #377304 and #378228. See page 3 for the consequences of interchanging these assemblies.