Johnson Service Bulletin SB-1148 - 20 H.P. Production Changes

November 1967. Johnson described two changes to 1967 FD(L)-21 20 H.P. motors intended to prevent water entering the powerhead through the carbon seal or oil drain system. The original three-page factory bulletin is reproduced below.

Johnson Motors Service Bulletin gray letterhead

November, 1967

SUBJECT:   20 H.P. PRODUCTION CHANGES

ON MODELS:  1967, FD(L)-21, 20 H.P.

Detailed in this bulletin are two production changes relative to the above model. The importance of making these changes to motors in the field can not be over emphasized as they will eliminate the possibility of water entering the powerhead via the Carbon Seal and/or Oil Drain System.

Due to the importance of these improvements, we are allowing $7.50 labor for each motor changed that is still under warranty. To alleviate the paperwork involved in this program, we request that you accumulate several jobs on one labor claim before submitting it to the factory. Be sure to list the model and serial numbers of each motor for which you are requesting labor allowance.

These changes do not affect motors produced after serial number:

FD-21, #J 2828837
FDL-21, #J 2842092

Contrary to this are nine (9) FDL-21 models which got ahead of the line and did not benefit from these changes. The serial numbers of these motors are:

FDL-21, #J 2842149 thru #J 2842158, inclusive

Change #1 Remove the Part Number 306210 Baffle Plate and one Part Number 306199 Gasket and discard. (Reference: 1967 - FD-21 Parts Catalog, page 11, items 1 and 2) See Figure 1.

Original Johnson Service Bulletin 1148 Figure 1
Figure 1
PAGE 2     SERVICE BULLETIN SB-1148
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085

Before reassembly, the following points must be investigated:

A.  Place the powerhead on the exhaust housing without any gasket and without the "O" ring on the driveshaft. Check that there is metal to metal contact between the top flange of the exhaust housing and the powerhead base (Figure 2).

B.  Check that there is clearance between the bottom of the cylinder head and mounting flange of the exhaust housing (Figure 2). If there is no clearance at this point, enough metal must be removed from the bottom of the cylinder head to afford visible clearance.

C.  Again check that there is metal to metal contact around the entire powerhead to exhaust housing junction.

D.  Install two bolts, one on each side of the engine, to secure the powerhead to the exhaust housing.

E.  Check to see if there is some crankshaft end play. If there is no end play, remove 1/16" from the top of the driveshaft. Repeat this step as required to achieve crankshaft end play.

Upon reassembly, thoroughly clean both driveshaft and crankshaft splines. Lightly lubricate all but one spline of the driveshaft with OMC type "A" lubricant. Leaving one spline dry will help avoid pneumatic action on the driveshaft caused by trapped air in the crankshaft cavity.

Original Johnson Service Bulletin 1148 Figure 2
Figure 2
PAGE 3     SERVICE BULLETIN SB-1148
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085

Change #2 Remove the Drain Valve, P/N 203235, and form so as to have a 1/64" to 1/16" arc. Do not kink. Form the arc as evenly as possible throughout the length of the valve (Fig. 3). Reinstall the Drain Valve and Valve Stop squarely over the drain holes. A pencil mark on the centerline of the drain holes will help you line up the Valve and Stop (Figure 4).

Original Johnson Service Bulletin 1148 Figure 3
Figure 3
Original Johnson Service Bulletin 1148 Figure 4
Figure 4
Original Johnson Service Bulletin 1148 Figure 5
Figure 5

After installation of Drain Valve, check to be sure it is seated well against the Crankcase. There should be no movement when you press down on the ends of the Valve (Figure 5).

JOHNSON MOTORS

Carl Klawonn
Administrative Assistant

CK/rkm

NOTE:  Post on your FD Index under the heading "Powerhead".

IMPORTANT NOTICE - Make the following correction to your 1968 - 20 H.P. "Preliminary Edition" Parts Catalog. Page 11, Item #1 now reads P/N 306199 Gasket, baffle; should read P/N 314421 Gasket.