Back to 1970-1980 OMC service bulletins

Evinrude Fuel System Bulletin #1019 - 1973 V4 Poor Idle or Hard Starting

Issued August 1973, this five-page factory bulletin documents carburetor synchronization, ignition timing, choke adjustments, neutral starting speed, and diagnosis of poor idle or carburetor spit-back on 1973 V4 outboards. The original technical procedures are reproduced as searchable text below.

Evinrude Service Bulletin factory letterhead
FUEL SYSTEM #1019
August, 1973

1973 V-4 ENGINES WITH POOR IDLE OR
HARD STARTING CHARACTERISTICS

Poor idle characteristics can generally be attributed to improper carburetor adjustments, improper synchronization, or too slow an idle speed.

I.   Carburetion

A.   The following list gives the order for making proper carburetor adjustments. This order must be followed in the sequence given. Section B will give details of the adjustments outlined in section A.

  1. Set TDC timing pointer.
  2. Synchronize the carburetor butterfly valves so that both valves fully close in the closed throttle position, they should also open at precisely the same time.
  3. Adjust center of cam follower to scribe mark on throttle cam.
  4. Start engine and adjust idle speed screw to obtain 4° on the timing grid. Stop engine.
  5. Adjust the throttle cam yoke so that the scribe mark on throttle cam aligns with the center of the cam follower. NOTE: One turn of yoke equals 2°, set pickup to 3° if 4° can not be obtained.
  6. Restart engine and adjust the idle stop screw to obtain a speed of 650 rpm in forward gear with the engine at normal operating temperature. Adjust the full spark advance stop screw to obtain a timing setting of 28° for the 85 hp, 26° for the 115 hp, 22° for the 135 hp, while the engine is running between 4300 and 4600 rpm in forward gear. Stop engine.
  7. Adjust the throttle stop screw, located on the starboard side of the crankcase, with the throttle lever in the full throttle position to obtain .010 clearance between the throttle cam and the throttle cam follower.

B.   The following are the details for the adjustments outlined in Section A.

1.   The synchronization of carburetion and ignition, and wide open throttle (WOT) timing depend upon the TDC pointer being properly set.

a.   Disconnect spark plug leads and remove spark plugs from engine.

b.   Install Piston Stop Tool #384887 into the number one cylinder spark plug hole and tighten snugly with spark plug wrench.

page 2

c.   Turn flywheel clockwise and adjust tool so that timing pointer aligns with the 30° mark on the flywheel timing grid. Lock tool into position with locknut. Recheck to see that pointer is still aligned with 30°.

d.   Rotate flywheel counterclockwise until piston contacts tool, and mark a line on the rim of flywheel opposite timing pointer.

e.   Using a machinist's scale, determine the midpoint between the line just described in the step above and the 30° mark on the timing grid of the flywheel. Mark this midpoint on the flywheel.

f.   Remove the Piston Stop Tool from the engine and rotate flywheel so that timing pointer aligns with the midpoint mark put on flywheel in step above. Now loosen the timing pointer adjustment screw and align pointer with the TDC mark on flywheel grid and retighten screw.

2.   The purpose of the following procedure is to eliminate all backlash in the carburetor linkage, and to ensure that both butterfly valves close completely and will open at the same time when the throttle cam follower is actuated by the throttle cam. To assist in making this adjustment it is advisable to remove the air silencer cover so you can observe the butterflies through the throat of the carburetors.

a.   Move the throttle linkage to the idle position.

b.   Loosen the throttle cam follower screw so the throttle cam follower will not touch the throttle cam.

c.   Loosen the throttle link fastener screw so you have a sliding friction fit between the linkage and the clamp.

d.   Hold the throttle shaft lever on the upper carburetor in the closed position while opening the bottom carburetor butterfly approximately 15°, about 1/6th of the way open.

e.   Let go of the upper carburetor butterfly shaft and now close the lower carburetor butterflies to a fully closed position.

f.   Carefully tighten the throttle link fastener screw.

g.   To ensure that this procedure has been done correctly, manually activate the throttle cam follower and note that both butterfly valves are opening at precisely the same time. With the aid of the flashlight look through the carburetor throats and note that all four butterfly valves will return to the fully closed position, if they do not return to the fully closed position make necessary adjustments or repairs to insure that they will. NOTE: If one butterfly closes and the other does not, remove the carburetor and by loosening the butterfly valves can be adjusted on the throttle shaft.

3.   Adjust the throttle cam follower so the mark on the throttle cam is in the center of the throttle cam follower when the carburetor butterflies just begin to open and retighten the throttle cam follower screw.

4.   Install timing light on number one cylinder. Start engine and adjust the idle speed screw to obtain a reading of 4° on the timing grid. Stop engine. NOTE: It may be necessary to partially unscrew the idle stop screw cap to ensure being able to reach 4° BTDC, reseat the idle stop screw cap before setting final idle speed.

5.   Adjust the throttle cam yoke so that the scribe mark on the throttle cam aligns with the center of the cam follower with the ignition at 4° BTDC.

page 3

Using a 1/2 inch wrench remove the throttle cam bolt and rotate the entire throttle cam and yoke assembly on the throttle lever link to perform the adjustment. Readjust the idle stop screw (reseat stop screw cap) to the approximate idle position and restart engine and observe that this adjustment is now correct. Since each turn of yoke moves the timing pickup 2°, set pickup to 3° if 4° cannot be obtained. Stop engine and reinstall air silencer cover.

6.   Restart engine and adjust the idle stop screw to obtain a speed of 650 rpm in forward gear with the engine at normal operating temperature. Adjust the full spark advance stop screw to obtain a timing setting of 28° for the 85 hp, 26° for the 115 hp, 22° for the 135 hp, while the engine is running between 4300 and 4600 rpm in forward gear. One turn of the full spark advance stop screw equals one degree in change of timing, turning the screw clockwise decreases the timing, turning the screw counterclockwise increases the timing. NOTE: Be sure engine is stopped before making any adjustments.

7.   Adjust the throttle stop screw (reference No. 64, page 16 1973 V-4 parts books) located on the starboard side of the crankcase, to obtain .010 clearance between the throttle cam and the throttle cam follower with the throttle lever in the full throttle position.

Hard starting characteristics are generally caused by improper choke settings or too slow a neutral starting speed.

I.   Choke Settings

A.   The following list gives points to be checked to ensure that the engine will receive full choking while activating the toggle switch or activating the full choke position of the choke knob.

1.   Some choke solenoids may not engage to the full choke position if the toggle switch is activated while cranking with weak solenoids or low battery voltage. To check for low battery voltage conditions attach voltmeter across the hot side of the starter solenoid and a good ground, and while cranking engine, battery voltage should not drop below 9 volts. Change or replace battery if necessary.

2.   To test for a defective solenoid perform the following test.

a.   With a "warm" engine, activate the toggle switch to energize the choke solenoid to the full choke position for 20 seconds to heat up choke solenoid.

b.   Release the choke solenoid to the no-choke position.

c.   Without the aid of the "cold engine-half choke" solenoid position (remove purple/yellow wire of choke solenoid from the terminal block if necessary), solenoid should now draw the plunger down to the full choke position when toggle switch is activated. If defective, replace with #386664, choke solenoid, for V-4 models, and #386675 for 50 hp, 60 hp, 65 hp, 70 hp models.

3.   With the choke butterflies in the open position adjust the choke solenoid body to obtain 5/16 of an inch between the top edge of the choke solenoid plunger shaft and the choke solenoid plunger lining in the choke solenoid body.

4.   With the air silencer cover removed from the engine, observe that both choke butterfly valves are fully closed when the choke solenoid is activated to the full choke position. Adjust linkage if necessary. In some cases the bottom choke butterfly strikes the bottom of the choke solenoid body in the full choke position, to correct this situation do the following.

page 4

a.   Screw the choke solenoid plunger spring completely onto the choke solenoid plunger.

b.   Readjust the choke solenoid as described in step 3 above.

c.   For a final check to see that the choke butterflies are closing fully, push down on the upper carburetor choke butterfly shaft lever pin and then tap the lower section of each butterfly valve to ensure that they are fully closed.

d.   Reinstall air silencer cover.

5.   To adjust the manual choke properly, perform the following steps.

a.   Place the manual choke knob in the automatic position.

b.   Check to see that there is a 1/16th of an inch gap between the manual choke spring #314981, and the choke arm and pin #383668.

c.   To adjust, loosen the detent lever shoulder screw and rotate the detent lever and detent lever spring as an assembly to obtain the 1/16th inch gap. Retighten shoulder screw.

II.   Neutral Starting Speed

A.   If the warmup lever of the remote control box does not advance the throttle lever on the engine enough to partially open the throttle butterflies, sufficient choking of the engine cannot be accomplished even though the choke butterflies are in the full choke position. The following list gives the order for making the proper warmup lever adjustment.

a.   With the remote control box in neutral and the warmup lever in the down position, adjust the throttle cable adjusting nut, located on the side of the carburetor air silencer, so the throttle stop screw will always return to the idle position. NOTE: If too much tension is applied to the throttle cable in the idle position the remote control box lever will have added resistance while moving from neutral to forward or reverse.

b.   With engine at normal operating temperature, adjust the warmup lever stop screw, located in the front of the remote control box, to allow the engine to reach 4500 rpm in neutral. NOTE: Readjust the starter safety switch located on the starboard side of the engine as necessary to allow you to make this warmup lever adjustment.

If all the foregoing steps have been performed and the engine still idles poorly or spits back through the carburetor, check the following items to determine the problem.

I.   Poor Idle

A.   Check orifices and all passages in carburetor for contamination of foreign material, remove carburetor and clean with compressed air if necessary. Check all carburetor screws for tightness, good gaskets, float level, butterfly valves not centered on throttle shaft, and seating in carburetor throat properly.

B.   Idle orifice screws that work loose during engine operation should be primed with OMC Locquic Primer (part #384884) and reinstalled using one drop of Screwlock (part #384848). Over-application of Screwlock may allow it to "creep" into the idle orifice causing partial blockage.

C.   Poor idle may be improved by installing Champion L-77J or AC M40FF spark

page 5

plugs gapped at .045.

1.   The 135 hp engine will not idle as smoothly as the 115 hp engine, nor will the 115 hp idle as smoothly as the 85 hp engine, this is due to the higher compression ratios of the more powerful engines.

D.   If poor idle is thought to be caused by one particular cylinder disconnect spark plug wires one at a time (do not touch wires with bare hands) while the engine is running at approximately 1000 rpm in neutral or forward gear and determine which cylinder is causing the problem.

1.   Using standard trouble shooting procedures as outlined in the service manual thoroughly trouble shoot the ignition system to determine if this is the cause of the problem.

2.   If necessary remove cylinder heads and check for scored cylinders or pistons.

II.   Engine Spits Back Through Carburetor

A.   If the engine is spitting back through the carburetor due to leanness, determine which cylinder is the cause of the problem by removing spark plug wires one at a time (do not touch wires with bare hands) while the engine is running at 1000 rpm, and look for one of the following items as a cause for the engine to spit back.

1.   Throttle butterfly not fully seating in the carburetor throat. Correct by reseating carburetor butterfly as outlined previously.

2.   Check to see that the leaf valves are seating correctly on the leaf plate and that the leaf stop screws are installed correctly and not allowing leakage by them. Also check to see that the leaf plate gasket is sealing correctly between the leaf plate assembly and the intake manifold. Using a straight-edge check to see that the leaf plate assembly gasket surface is flat, resurface on a good true surfacing block if necessary, also check to see that the intake manifold surface where the leaf plate gasket seats is flat.

3.   Check to see that there are no signs of improper sealing between the crankcase and intake manifold. If the surfaces are warped or nicked resurface as necessary.

4.   Check to see that there are no signs of improper sealing around the intake bypass covers. If so resurface as necessary.

B.   If the engine still spits back through the carburetor due to leanness and the cause has not been found replace the idle orifices on 115 hp engines with #320016 (.032), 135 hp engines with #320015 (.033).

EVINRUDE MOTORS
Service Department