Evinrude Service Bulletin #1116

Steering, permanently installed fuel systems, and drywell drain-hole recommendations for boats with 150 HP or more.

Evinrude Service Bulletin header
February, 1976 STEERING SYSTEM, FUEL SYSTEM AND DRYWELL DRAIN HOLE RECOMMENDATIONS FOR ALL SINGLE OR DUAL ENGINE INSTALLATIONS TOTALING 150 H.P. OR MORE NOTE The attached letter and recommendation sheets have been sent to all boat builders to guide them in their design and planning for current and future outboard powered boats. If your dealership installs steering systems and/or permanently installed fuel tanks in boats with 150 H.P. or more, you must follow these recommendations completely to insure your customers of a safe, reliable rig. EVINRUDE MOTORS Service Department
Original bulletin 1116, page 2
Miscellaneous #1116 TO: Boat Builders FROM: Outboard Marine Corporation SUBJECT: Drywell Drain Holes The trend toward power trim and tilt on large outboards has indicated to OMC that it should be an integral part of larger outboards as was done on the 200 h.p. The OMC V-6 integral power tilt and trim mechanism was designed for best appearance and function. It is a unitized design without extemal hydraulic connections for ease of motor installation. It may result in the motor covering up the center located drywell drain holes on some outboard boats. For this reason, we recommend that drywell drain holes be placed at least eight (8) inches off the center- line of the boat to allow the drywell to drain properly. TO: Boat Builders FROM: Outboard Marine Corporation SUBJECT: Permanently Installed Fuel Systems This is a design guide for built-in fuel systems on boats using OMC outboards of more than 150 gross horsepower (i.e. dual V-4 or single V-6 installations). Following the recommendations listed below will insure trouble free performance for the customer: TANK PICKUP TUBE - Should be minimum 5/16’’ |.D. - 3/8’ |.D. is preferred. PICKUP TUBE SCREEN - Recommend stainless steel #304 wire cloth, 100 x 90 mesh, .0045 aiameter wire with a total open area not less than .170 sq. inches. ANTI-SIPHON VALVE - Anti-syphon valves should have a pressure drop of no more than 35 inches (maximum) of water at a fuel flow rate of 20 gallons per hour. The following OMC valves which meet the above criteria are available: #173273 for 5/16’’ 1.D. Hose #173274 for 3/8°’ |.D. Hose #173275 for 3/8’’ O.D. Copper Tube FUEL DISTRIBUTION LINES (From Tank to Drywell Fitting) - Minimum 5/16’’ |.D. (3/8"’ 1.D. preferred). OMC #319719 hose (5/16"’ I.D.) or OMC #123111 (3/8" I.D.) hose or 3/8’’ 0.D. copper tube may be used. The OMC hose is available in 25 Ft. lengths. All fittings must be a minimum of 1/4’’ |.D. Be sure lines are free of kinks and sharp bends. FILTER - If a fuel filter is installed it should have no more than 5 inches of water pressure drop at a fuel flow rate of 20 gallons per hour. The filter should have a minimum filter area of 200 square inches. The OMC #173310 filter will be available which meets the foregoing criteria. DO NOT use OMC #377381 primer kit if engines of over 150 h.p. are installed. FUEL LINE (From Drywell Fitting to Engine) - OMC #173277 hose, primer bulb and fuel connector kit are available for connecting from a bulkhead fitting in the drywell to the engine. This kit also provides for priming of the engine. Additionally, we recommend that ABYC standard H-24 be followed to insure a safe installation for the entire built-in fuel system.
Miscellaneous #1116 TO: Boat Builders FROM: Outboard Marine Corporation SUBJECT: Steering System Requirements - Johnson and Evinrude V-6 Outboards r In the Johnson and Evinrude V-6 ‘’Owner’s Manuals" and the “Steering System Selection Guide,"’ which are packaged with the outboard motor as the dealer receives it, there is a precautionary note which state ‘‘on boats that are capable of speeds in excess of 40 mph with a single engine, a twin cable system may be necessary if instability occurs.” The purpose of this memo is to clarify the intent of this precaution and to negate the industry wide misunderstanding that twin cable steering is required on all V-6 powered boats with speed capability in excess of 40 mph. The precautionary note in the Owner’s Manuals is not intended to infer that a higher strength system is required to handle steering loads generated by the outboard. The Johnson and Evinrude V-6, thru improved steering geometry, does not impose greatly increased loads over those experienced with 135 h.p. engines. The aim is to reduce free play in the steering system to a minimum. A single cable system capable of meeting the strength standards specified in ABYC P-17 as proposed October 21, 1974, will be adequate for Johnson and Evinrude V-6 engine installation unless it con- tributes to instability. The ‘‘instability’’ referred to is commonly called ‘‘fishtailing’’ which is the tendency for the stern of a boat to move side to side even when the steering wheel is held in a fixed position. Fishtailing gives the boat an insecure feel, and it is reasonable to assume that such a feeling could lead to over reaction by the driver. Contributing factors are: VY 1. Height and tilt angle of motor relative to the surface of the water. 2. Speed. 3. Surface condition of water. 4. Free play or “‘backlash’’ of a steering system. 5. Regidity of the motor mounting surface (transom). 6. Type of boat hull. The boat builder should test to determine if instability is a problem with their particular hull and steering configurations. Fishtailing occurs most noticeably when performing high speed shallow tums in a light to medium surface chop and with lightest loads. Corrective action may be: 1, Engine height and tilt angle are generally determined by owner or dealer. However, the boat should be stable over a reasonable range of engine heights and tilt angles. 2&3. Again, boat should be tested for stability at the extremes of expected water and speed conditions. 4. Choose a single cable steering system with a minimum of free play or a twin cable system where free play can be reduced by adjustment. 5. Increase stiffness of transom. 6. Hull redesign for greater stability. Such a twin cable system is available by utilizing OMC Rotomatic | steering or equivalent with two #172645 Transom Brackets and one #173257 Dual Cable Connector Kit. Such systems must be installed with the free play adjusted to a minimum at the straight ahead position. .) Some high speed boats may require the installation of more rigid motor mounts. These are available (Part #387998). Installation of these mounts will increase the engine noise level and vibration transmission.