Evinrude Service Bulletin 1144 - 1976 70 and 75 HP Mid-Range Improvement

Issued September 1976, this factory service bulletin describes diagnosis of mid-range hesitation and two remedies: modifying existing carburetors or exchanging them for recalibrated units.

Evinrude service bulletin header
FUEL SYSTEM #1144
September, 1976

1976 70 and 75 H.P. MID-RANGE IMPROVEMENT

Some of the '76 Evinrude 3 cylinder motors have developed a flat spot or hesitation, and in some severe cases, a tendency to die during mid-range acceleration such as when pulling up skiers. If blipping the choke momentarily helps the motor accelerate thru the mid-range R.P.M., a lean carburetion condition is indicated and the mid-range performance may be improved by making the carburetor modifications or carburetor exchange detailed below.

In all cases, if unsatisfactory performance is reported, you should first:

Check to see that no propeller ventilation is occurring during acceleration. If ventilation is present, change motor position as required.

Check to see that the motor is running at the maximum operating R.P.M. at wide open throttle (W.O.T.) with one person on board (5500 R.P.M. for 70 H.P. & 5800 R.P.M. for 75 H.P.). Change propeller to get this R.P.M.

Check to see that the motor timing and synchronization are properly adjusted.

This includes:
1. Full spark advance setting (17° for 70 and 16° for 75 H.P.)
2. Throttle linkage synchronization (All throttle valves closed, back-lash out of linkage with roller off cam).
3. Throttle cam adjustment (embossed throttle cam mark on roller center-line at pick-up point, that is when throttle shafts start to rotate).
4. Throttle cam - spark advance synchronization (Throttle cam pick-up at top dead center, T.D.C. - adjust yoke on throttle rod to set).

If there is NO ventilation, motor is at maximum operating R.P.M. at W.O.T., motor is CORRECTLY timed and synchronized, and motor appears to be running lean during mid-range acceleration, the carburetors may either be modified or replaced. Details of either approach are listed below.

I. CARBURETOR MODIFICATION
The carburetors may be modified as detailed below and a warranty allowance request filed for 3.0 hours labor, total, including testing, and material replacement or credit voucher for the following:

3 - Core PlugP/N 306442
3 - Idle OrificeP/N 320016
4 - Clamp StrapP/N 320107
3 - Carburetor GasketP/N 314477
(over)
Factory page 2: carburetor modification steps 1 through 5 with figures 1 through 5
Figure 6: .032 idle jet, part 320016

6. Remove the .030 idle orifice, shake and blow out any drill chips, and install the .032 idle orifice P/N 320016. See Figure 6.

7. Apply a VERY SMALL amount of OMC Adhesive M very carefully to the outer edge of the new core plug and install, flattening with a punch. Seal plug with Adhesive M.

8. Use a metal stamp or chisel to mark the top of the carburetor with an “X” and re-assemble the carburetor. See Figure 4. Repeat the modifications on other two carburetors.

II. CARBURETOR REPLACEMENT

If you prefer to install re-calibrated carburetors that are available on an exchange basis, you may submit a warranty claim to Evinrude Service Department for 2.5 hours labor, total, including testing, and the 70 H.P. or 75 H.P. re-calibrated carburetors and associated parts listed below. You will be charged for the carburetors until the old ones have been returned to Evinrude Service Department. The components required for the carburetor exchange are:

70 H.P. Exchange Components:
1 - Middle CarburetorP/N 387904
2 - Upper & Lower CarburetorP/N 387905
4 - Clamp StrapP/N 320107
3 - Carburetor GasketP/N 314477
75 H.P. Exchange Components:
1 - Middle CarburetorP/N 387906
2 - Upper & Lower CarburetorP/N 387907
4 - Clamp StrapP/N 320107
3 - Carburetor GasketP/N 314477

Whether modifying or exchanging carburetors, next install carburetors, using the throttle adjustment levers, washers and screws from the old carburetors, carefully synchronize the throttle and choke linkage, check the throttle cam adjustment, and the throttle cam - spark advance synchronization as detailed above and in service manual. Test motor before delivery to customer.

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Carburetor Cleaner Spray, Jet Cleaning Wires & Rebuild Kit

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 3064423

Search for original or compatible replacement part 3064423. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.