Johnson Service Bulletin SB-1322 (July 1973) - 1973 V-4 Poor Idle or Hard Starting

Seven-page factory troubleshooting bulletin covering 1973 Johnson V4 carburetor synchronization, ignition timing, choke adjustments, neutral starting speed, poor idle and carburetor spit-back. Includes piston stop tool 384887 and Phase II pulse pack guidance.

Johnson Service Bulletin letterhead
SB-#1322
July, 1973

SUBJECT: 1973 V-4 ENGINES POOR IDLE CHARACTERISTICS OR HARD STARTING
CHARACTERISTICS

Poor idle characteristics can generally be attributed to improper
carburetor adjustments, improper synchronization, or too slow an
idle speed,

I. Carburetion

A. The following list gives the order for making proper carburetor
adjustments, This order must be followed in the sequence given,
Section B will give details of the adjustments outlined in this
section,

1. Set TDC timing pointer,

2. Synchronize the carburetor butterfly valves so that both valves
fully close in the closed throttle position, they should also
open at precisely the same time.

3. Adjust center of cam follower to scribe mark on throttle cam,

4. Start engine and adjust idle speed screw to obtain 4° on the
timing grid, Stop engine,

5. Adjust the throttle cam yoke so that the scribe mark on
throttle cam aligns with the center of the cam follower.,
NOTE: One turn of yoke equals 2°, set pickup to 3° if 4°
can not be obtained,

6. Restart engine and adjust the idle stop screw to obtain a
speed of 650 rpm in forward gear with the engine at normal
operating temperature, Adjust the full spark advance stop
screw to obtain a timing setting of 28° for the 85 HP, 26
for the 115 HP, 22° for the 135 HP, while the engine is run-
ning between 4300 and 4600 rpm in forward gear, Stop engine.

7. Adjust the throttle stop screw, located on the starboard side
of the crankcase, with the throttle lever in the full throttle
position to obtain .010 clearance between the throttle cam
and the throttle cam follower,
PAGE 2SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
B. The following are the details for the adjustments outlined in
Section A.

4. The synchronization of carburetion and ignition, and WOT
timing depend upon the TDC pointer being properly set.

a, Disconnect spark plug leads and remove spark plugs from
engine.

b, ‘Install Piston Stop Tool #384887 into the number one cylinder
spark plug hole and tighten snugly with spark plug wrench.

Turn flywheel clockwise and adjust tool so that timing
pointer aligns with the 30° mark on the flywheel timing
grid. Lock tool into position with locknut, Recheck to
see that pointer is still aligned with 30°.

Rotate flywheel counterclockwise until piston contacts tool,
and mark a line on the rim of flywheel opposite timing
pointer,

Using a machinist's scale, determine the midpoint between
the line just described in the step above and the 30° mark
on the timing grid of the flywheel, Mark this midpoint on
the flywheel.

Remove the Piston Stop Tool from the engine and rotate
flywheel so that timing pointer aligns with the midpoint
mark put on flywheel in step above, Now loosen the timing
pointer adjustment screw and align pointer with the TDC
mark on flywheel grid and retighten screw,

2, The purpose of the following procedure is to eliminate all
backlash in the carburetor linkage, and to ensure that both
butterfly valves close completely and will open at the same
time when the throttle cam follower is actuated by the throttle
cam, To assist in making this adjustment it is advisable
to remove the air silencer cover so you can observe the
butterflies through the throat of the carburetors,

a, Move the throttle linkage to the idle position,

b, Loosen the throttle cam follower screw so the throttle cam
follower will not touch the throttle cam,

. Loosen the throttle link fastener screw so you have a
sliding friction fit between the linkage and the clamp,

 d. Hold the throttle shaft lever on the upper carburetor in the
closed position while opening the bottom carburetor butterfly
approximately 15°, about 1/6th of the way open.

e. Let go of the upper carburetor butterfly shaft and now close
the lower carburetor butterflies to a fully closed position.
PAGE 3SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
Carefully tighten the throttle link fastener screw.

g. To ensure that this procedure has been done correctly manually
activate the throttle cam follower and note that both
butterfly valves are opening at precisely the same time,

With the aid of a flashlight look through the carburetor
throats and note that all four butterfly valves will return
to the fully closed position, if they do not return to the
fully closed position make necessary adjustments or repairs
to insure that they will. NOTE: If one butterfly closes

and the other does not, remove the carburetor and by loosening
the butterfly valve screws the butterfly valves can be
adjusted on the throttle shaft.

3. Adjust the throttle cam follower so the mark on the throttle
cam is in the center of the throttle cam follower when the
carburetor butterflies just begin to open and retighten
throttle cam follower screw,

4. Install timing light on number one cylinder. Start engine and
adjust the idle speed screw to obtain a reading of 4° on the
timing grid, Stop engine, NOTE: It may be necessary to
partially unscrew the idle stop screw cap to ensure being
able to reach 4° BTDC, reseat the idle stop screw cap before
setting final idle speed, [ )

5. Adjust the throttle cam yoke so that the scribe mark on the
throttle cam aligns with the center of the cam follower with
the ignition at 4° BTDC., Using a 1/2 inch wrench remove the
throttle cam bolt and rotate the entire throttle cam and
yoke assembly on the throttle lever link to perform the
adjustment. Readjust the idle stop screw (reseat stop screw
cap) to the approximate idle position and restart engine and
observe that this adjustment is now correct, Since each,
turn of yoke moves the timing pickup 2°, set pickup to 3° if
4° can not be obtained, Stop engine and reinstall air
silencer cover,

6, Restart engine and adjust the idle stop screw to obtain a
speed of 650 rpm in forward gear with the engine at normal
operating temperature. Adjust the full spark advance stop
screw to obtain a timing setting of 28° for the 85 HP, 26
for the 115 HP, 22° for the 135 HP, while the engine is
running between 4300 and 4600 rpm in forward gear, One
turn of the full spark advancement stop screw equals one
degree in change of timing, turning the screw clockwise
decreases the timing, turning the screw counterclockwise
increases the timing. NOTE: Be sure engine is stopped
before making any adjustments,

7. Adjust the throttle stop screw (reference No. 64, page 16 1973 @
V-4 parts books) located on the starboard side of the crankcase,
to obtain .010 clearance between the throttle cam and the
throttle cam follower with the throttle lever in the full
throttle position,
PAGE 4SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
Hard starting characteristics are generally caused by improper choke
settings or too slow a neutral starting speed.

I. Choke Settings

A. The following list gives points to be checked to ensure that
the engine will receive full choking while activating the toggle
switch or activating the full choke position of the choke knob,

Some choke solenoids may not engage to the full choke position
if the toggle switch is activated while cranking the engine with
the starter motor, This is due to a combination of possibly
weak solenoids or low battery voltage. To check for low
battery voltage conditions attach voltmeter across the hot side
of the starter solenoid and a good ground, and while cranking
engine, battery voltage should not drop below 9 volts, Change
or replace battery if necessary.

To test for a defective solenoid perform the following test.

a, With a "warm" engine, activate the toggle switch to energize
the choke solenoid to the full choke position for 20 seconds
to heat up choke solenoid,

b. Release the choke solenoid to the no-choke position.

c. Without the aid of the "cold engine-half choke" solenoid
position (remove purple/yellow wire of choke solenoid from
the terminal block if necessary), solenoid should now draw
the plunger down to the full choke position when toggle
switch is activated, If defective, replace with #386664,
choke solenoid, for V-4 models, and #386675 for 50 HP, 60 HP,
65 HP, 70 HP models,

3. With the choke butterflies in the open position adjust the
choke solenoid body to obtain 5/16 of an inch between the
top edge of the choke solenoid plunger shaft and the choke
solenoid plunger lining in the choke solenoid body,

4. With the air silencer cover removed from the engine, observe that
both choke butterfly valves are fully closed when the choke
solenoid is activated to the full choke position, Adjust
linkage if necessary, In some cases the bottom choke butterfly
strikes the bottom of the choke solenoid body in the full
choke position, to correct this situation do the following.

a, Screw the choke solenoid plunger spring completely onto the
choke solenoid plunger,

(b. Readjust the choke solenoid as described in step 3 above,

c. For a final check to see that the choke butterflies are
closing fully, push down on the upper carburetor choke
PAGE 5SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
butterfly shaft lever pin and then tap the lower section
of each butterfly valve to ensure that they are fully closed,

a, Reinstall air silencer cover,

5. To adjust the manual choke properly perform the following
steps,

a, Place the manual choke knob in the automatic position,

b. Check to see that there is a 1/16th of an inch gap between
the manual choke spring #314981, and the choke arm and pin
#383668,

c. To adjust, loosen the detent lever shoulder screw and
rotate the detent lever and detent lever spring as an
assembly to obtain the 1/16th inch gap, Retighten shoulder
screw.

II. Neutral Starting Speed

A. If the warmup lever of the remote control box does not advance
the throttle lever on the engine enough to partially open the
throttle butterflies, sufficient choking of the engine cannot e
be accomplished even though the choke butterflies are in the
full choke position, The following list gives the order for
making the proper warmup lever adjustment.

a, With the remote control box in neutral and the warmup lever
in the down position, adjust the throttle cable adjusting
nut, located on the Side of the carburetor air silencer,
so the throttle stop screw will always return to the idle
position, NOTE: If too much tension is applied to the
throttle cable in the idle position the remote control box
lever will have added resistance while moving from neutral
to forward or reverse.

b, With engine at normal operating temperature, adjust the
warmup lever stop screw, located in the front of the remote
control box, to allow the engine to reach 4500 rpm in neutral,
NOTE: Readjust the starter safety switch located on the
starboard side of the engine as necessary to allow you to
make this warmup lever adjustment.
PAGE 6SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
If all the foregoing steps have been performed and the engine still
idles poorly or spits back through the carburetor, check the following
items to determine the problem.

I. Poor Idle

Check orifices and all passages in carburetor for contamination
of foreign material, remove carburetor and clean with compressed
air if necessary, Check all carburetor screws for tightness,
good gaskets, float level, butterfly valves not centered on
throttle shaft, and seating in carburetor throat properly.

Idle orifice screws that work loose during engine operation should
be primed with OMC Locquic Primer (part #384884) and reinstalled
using one drop of Screwlock (part #384848), Overapplication of

Screwlock may allow it to "creep" into the idle orifice causing
partial blockage,

C. Poor idle may be improved by installing Champion L-773 or AC M40FF
spark plugs gapped at .045.

1. The 135 HP engine will not idle as smoothly as the 115 HP engine,
nor will the 115 HP idle as smoothly as the 85 HP engine,
this is due to the higher compression ratios of the more

D, If poor idle is thought to be caused by one particular cylinder
disconnect spark plug wires one at a time (do not touch wires with
pare hands) while the engine is running at approximately 1000 rpm
in neutral or forward gear and determine which cylinder is
causing the problem,

1, Using standard trouble shooting procedures as outlined in the
service manual thoroughly trouble shoot the ignition system
to determine if this is the cause of the problem,

2, If necessary remove cylinder heads and check for scored
cylinders or pistons,

II. Engine Spits Back Through Carburetor

A. If the engine is spitting back through the carburetor due to
leanness, determine which cylinder is the cause of the problem
by removing spark plug wires one at a time (do not touch wires
with bare hands) while the engine is running at 1000 rpm, and
look for one of the following items as a cause for the engine
to spit back.

1, Throttle butterfly not fully seating in the carburetor throat,
Correct by reseating carburetor butterfly as outlined previously

Check to see that the leaf valves are seating correctly on the
leaf plate and that the leaf stop screws are installed
PAGE 7SERVICE BULLETIN   SB-#1322
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
correctly and not allowing leakage by them, Also check to see
that the leaf plate gasket is seating correctly between the
leaf plate assembly and the intake manifold. Using a straight-
edge check to see that the leaf plate assembly gasket surface
is flat, resurface on a good true surfacing block if necessary,
also check to see that the intake manifold surface where the
leaf plate gasket seats is flat,

3. Check to see that there are no signs of improper sealing
between the crankcase and intake manifold, If the surfaces
are warped or nicked resurface as necessary,

1. Check to see that there are no signs of improper sealing
around the intake bypass covers, If so resurface as necessary,

B. If the engine still spits back through the carburetor due to
leanness and the cause has not been found replace the idle
orifices on 115 HP engines with #320016 (.032), 135 HP engines
with #320015 (.033).

JOHNSON OUTBOARDS

Dale J, Leinonen
Technical Data Coordinator

DJL/lcb
NOTE: Post on 85-115 and 135 indexes under heading "Carburetion",

FOOTNOTE: Outboard Marine Engineering has advised that when
replacing the original pulse pack on V4TL-13 and V4TL-14
with the new Phase II pulse pack remove the voltage
suppressor part #580732 at the time the Phase II pack is
installed, the original rotor must be replaced with the
new style rotor supplied with the Phase II replacement
pack, The voltage suppressor should not be removed from
V4TL-13 and V4TL-14 engines which have the original
pulse pack,

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Inductive Ignition Timing Light & Feeler Gauge Set

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 384887

Search for original or compatible replacement part 384887. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.