SB-1429 - Mid-Range Improvement
Issued September 1976, this four-page Johnson Service Bulletin describes mid-range hesitation on 1976 Johnson 70 and 75 H.P. three-cylinder outboards. It includes diagnosis, ignition synchronization, carburetor recalibration procedures, original illustrations, and exchange part numbers. The factory instructions are searchable below.

SB-#1429
September, 1976
SUBJECT: Mid-Range Improvement
ON MODELS: 1976 - 70 and 75 H.P.
Some of the '76 Johnson 3 cylinder motors have developed a flat spot or
hesitation, and in some severe cases, a tendency to die during mid-range
acceleration such as when pulling up skiers. If blipping the choke
momentarily helps the motor accelerate thru the mid-range R.P.M., a lean
carburetion condition is indicated and the mid-range performance may be
improved by making the carburetor modifications or carburetor exchange
detailed below.
In all cases, if unsatisfactory performance is reported, you should first:
Check to see that no propeller ventilation is occurring during
acceleration. If ventilation is present, change motor position
as required.
Check to see that the motor is running at the maximum operating
R.P.M. at wide open throttle (W.O.T.) with one person on board
(5500 R.P.M. for 70 h.p. and 5800 R.P.M. for 75 h.p.). Change
propeller to get this R.P.M.
Check to see that the motor timing and synchronization are
properly adjusted.
This includes:
1. Full spark advance setting (17° for 70 and 16° for 75 h.p.)
2. Throttle linkage synchronization (all throttle valves
closed, back-lash out of linkage with roller off cam).
3. Throttle cam adjustment (embossed throttle cam mark on
roller center-line at pick-up point, that is when throttle
shafts start to rotate).
4. Throttle cam - spark advance synchronization (Throttle cam
pick-up at top dead center, T.D.C. - adjust yoke on throttle
rod to set).
PAGE 2 SERVICE BULLETIN #1429
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
If there is no ventilation, motor is at maximum operating R.P.M. at W.O.T.,
motor is CORRECTLY timed and synchronized, and motor appears to be running
lean during mid-range acceleration, the carburetors may either be modified
or replaced. Details of either approach are listed below.
I. CARBURETOR MODIFICATION
The carburetors may be modified as detailed below and a warranty
allowance request filed for 3.0 hours labor, total, including testing
and material replacement or credit voucher for the following:
3 - Core Plug P/N 306442
3 - Idle Orifice P/N 320016
4 - Clamp Strap P/N 320107
3 - Carburetor Gasket P/N 314477
If you wish to modify the carburetors:
1. Remove air silencer, linkage and fuel lines from carburetors
and remove carburetors.
2. Remove float bowl and float.
3. Use a #55 (.052) drill in a pin vise to ream out the four holes
in the high-speed nozzle. Drill only far enough to go thru the
nozzle wall, without damaging the idle pick-up tube inside. See
figures 1 and 2. DO NOT use any other number size, letter size,
or fractional size drills except those recommended for these or
any of the other drilled holes in this modification. DO NOT use
an electric drill. If a pin vise is not available, wrap tape
around the drill shank to increase shank size for a better grip.
Drill all holes straight thru carefully. Egg shaped holes will
result in improper calibration. Remove any burrs inside nozzle.
Do not bend the pick-up tube inside the high-speed nozzle from
its off-center position.


PAGE 3 SERVICE BULLETIN #1429
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
4. Drive a 1/8 inch pin punch just thru the core plug covering
the calibration pocket and pry out the plug. See Figure 3.
5. Use a #56 (.046) drill to enlarge the two outer calibration
ports and a #57 (.043) drill to enlarge the center port. See
Figures 4 and 5. Observe all of the precautions stated above.
6. Remove the .030 idle orifice, shake and blow out any drill
chips, and install the .032 idle orifice P/N 320016. See
Figure 6.
7. Apply a VERY SMALL amount of the OMC Adhesive M very carefully
to the outer edge of the new core plug and install, flattening
with a punch. Seal plug with Adhesive M.
8. Use a metal stamp or chisel to mark the top of the carburetor
with an "X" and reassemble the carburetor. See Figure 4.
Repeat the modifications on other two carburetors. After
carburetors are installed spray orange paint on the port side
of the carburetors for quick future identification.




PAGE 4 SERVICE BULLETIN #1429
JOHNSON OUTBOARDS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60085
II. CARBURETOR REPLACEMENT
If you prefer to install re-calibrated carburetors that are available
on an exchange basis, you may submit a warranty claim to Johnson
Outboards Service Department for 2.5 hours labor, total, including
testing, and the 70 h.p. or 75 h.p. re-calibrated carburetors and
associated parts listed below. You will be charged for the carburetors
until the old ones have been returned to Johnson Outboards Service
Department. The components required for the carburetor exchange are:
70 H.P. Exchange Components:
1 - Middle Carburetor P/N 387904
2 - Upper and Lower Carburetor P/N 387905
4 - Clamp Strap P/N 320107
3 - Carburetor Gasket P/N 314477
75 H.P. Exchange Components:
1 - Middle Carburetor P/N 387906
2 - Upper and Lower Carburetor P/N 387907
4 - Clamp Strap P/N 320107
3 - Carburetor Gasket P/N 314477
Whether modifying or exchanging carburetors, next install carburetors,
using the old throttle adjustment levers and screws carefully synchro-
nize the throttle and choke linkage, check the throttle cam adjustment
and the throttle cam - spark advance synchronization as detailed above
and in service manual. Test motor before delivery to customer.
JOHNSON OUTBOARDS
D. J. Leinonen
Technical Data Coordinator
DJL/kr
NOTE: The 70 and 75 h.p. carburetors that are shipped from the Johnson
Outboards Service Department will be painted stinger orange on
the port side. When servicing the orange marked carburetors or
those with the "X" on the top be sure that only .032 idle
orifices are used.
NOTE: Post on your 70 and 75 h.p. index under heading "Carburetion".