Johnson Service Bulletin SB-1535 (May 1980) - Improved Bearing and Gear Kits

Johnson's 1980 service bulletin identifies updated forward gear and anti-friction bearing kits for 1960-1979 18, 20 and 25 HP outboards, three-lug clutch dog conversion kits, and special gearcase assembly tool P/N 390880.

Johnson Service Bulletin letterhead
SB - 1535
May, 1980

Subject: Improved Bearing and Gear Kits / Special Tool P/N 390880

Models: 1960 thru 1979 18, 20 and 25 H.P. Outboards

Several new service kits have been released to improve the service life of older 18, 20 and 25 H.P. gearcases.

1. There are two forward gear and anti-friction bearing kits to replace the forward gear and bronze friction-type forward bearing used in the 1960 thru 1978 18, 20 and 25 H.P. models. The 1979 and later 25 H.P. models were originally equipped with the anti-friction type forward bearings.
A. 1960 thru 1970 18-25 H.P. models
1971 20 H.P. with “F” model suffix

Use Kit P/N 390970. See Figure 1.

Contents of Kit
Ref. No.Part No.DescriptionQty.
1326078Thrust Washer - Forward Gear1
2390971Gear and Bushing Assy. - Forward1
3389470Thrust Bearing Assy. - Forward Gear1
4389472Needle Bearing Assy. - Forward Gear1
B. 1971 20 H.P. with “S” model suffix
1972 thru 1978 20-25 H.P. model

Use Kit P/N 390972. See Figure 1.

Contents of Kit
Ref. No.Part No.DescriptionQty.
1326078Thrust Washer - Forward Gear1
2390973Gear and Bushing Assy. - Forward1
3389470Thrust Bearing Assy. - Forward Gear1
4389472Needle Bearing Assy. - Forward Gear1
Figure 1, forward gear thrust washer and bearing kits 390970 and 390972
CR 79-78   © OUTBOARD MARINE CORPORATION 1980 ALL RIGHTS RESERVED
2. If frequent shifter dog replacements have been required on 1960 thru 1979 18-25 H.P. models, due to severe or commercial applications, there are kits to equip the gearcase with the 3-lug shifter dog similar to that used in the 1980 25 H.P. models.

Kit P/N 390974, for 1960 thru 1978 18 and 25 H.P. models, includes the anti-friction type bearings for the forward gear. The 1979 and later 25 H.P. models were originally equipped with the anti-friction bearing.
A. 1960 thru 1978 18-25 H.P. models

Use Kit P/N 390974. See Figure 2.

Contents of Kit
Ref. No.Part No.DescriptionQty.
1302493O-Ring1
2309044Seal - Upper Lower Gearcase1
3325014Cradle - Clutch Dog1
4325258Gear - Reverse1
5325263Shifter - Clutch Dog1
6326078Thrust Washer - Forward Gear1
7389470Thrust Bearing Assy. - Forward Gear1
8389472Needle Bearing - Forward Gear1
9390975Gear and Bushing Assy. - Forward1
B. 1979 25 H.P. models

Use Kit P/N 391019. See Figure 3.

Contents of Kit
Ref. No.Part No.DescriptionQty.
1390295Gear and Bushing Assy.1
2325263Shifter - Clutch Dog1
3325258Gear - Reverse1
Figure 3, gear and clutch dog kit 391019 Figure 2, forward and reverse gear bearing and clutch dog kit 390974
3. Special Tool P/N 390880

All 18, 20 and 25 H.P. models, equipped with the anti-friction type forward bearings, require the correct preload of these bearings and proper alignment for reassembly. The use of special tool P/N 390880 is required for proper reassembly. When assembling a gearcase, first hook the tool into the groove of the gearcase head. Then turn the finger screw snugly into the end of the propeller shaft. This will push the thrust bearings and washers forward while pulling the gearcase head rearward, properly preloading and aligning the bearings for correct installation of the lower gearcase half. See Figure 4.
Figure 4, special tool 390880 in use
The tool, P/N 390880, must remain in place until after the gearcase halves have been reassembled and the gearcase screws are properly torqued (40-60 in. lbs.).
NOTE: Post on 20 - 25 hp index under heading “Lower Unit.”

Related factory references

Special tool P/N 390880 is used to preload and align anti-friction forward gear bearings while reassembling the lower gearcase. Factory kits: 390970, 390972, 390974 and 391019.

1970-1980 Johnson Service Bulletin Index

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Bearing Race & Seal Driver Set + Marine Assembly Grease

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 390880

Search for original or compatible replacement part 390880. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.