Johnson SPB-491 (March 1979) - Time and Labor Saving Shop Equipment

Four-page Johnson Service Promotion Bulletin featuring Kerr's Marine Tool Company motor stands, lower-unit fixtures, propeller pullers, hydraulic lifting equipment and a test tank.

Johnson Outboards Service Promotion letterhead
SPB # 491

March 1979

SUBJECT- TIME AND LABOR SAVING SHOP EQUIPMENT:

Talk about making the job easier- well that's just what Bob Kerr of Kerr's Marine Tool Company has done by designing the following illustrated shop equipment for service on OMC outboards and outdrives.

Original factory photograph of 1000 hydra tilt

#1000 H.D. HYDRA-TILT MOTOR STAND

This new hydraulic operated motor stand will accommodate any size engine and comes with these standard features: 18"x18" floor plate, adjustable flow control valve for safety. 360° rotation on the stand base. 90° engine rotation for easy lower unit access. Built in adaptability for use with all lower unit and powerhead fixtures.

Original factory photograph of 1000c motor stand

#1000-C OUTBOARD MOTOR STAND

Worm-gear operated motor Stand. Just turn the handle and motor rotates easily and safely to any desired position. Aset collar allows the operator to adjust stand to his working height. New cast aluminum head assembly. ca. 250lbs.

SHEET 2
Original factory photograph of 400 lower unit fork

#400 - HD LOWER UNIT UNIT FORK

Rotates in the #600B base holding all small lower units. This allows the mechanic to work with both hands free at all times. New stronger aluminum casting.

Original factory photograph of 400l large lower unit

#400L-HD LARGE LOWER UNIT

FOR ALL OUTBOARDS AND OUTDRIVES.

Original factory photograph of 600se engine bracket

#600SE-SMALL ENGINE BRACKET

For use with 600B on bench or motor stand. Capacity 25 HP.

Original factory photograph of 70 omc puller

#70 OMC PULLER WITH #1 PILOT

For pulling OMC lower units

Original factory photograph of 80 propeller puller

#80 PROPELLER PULLER. IT'S NEW!

It will pull 2,3, or 4 blade props. Stop pounding the prop with a mallet - the puller makes a hard job easy.

SHEET 3
Original factory photograph of 1800 hydra press

#1800 HYDRA-PRESS

Heavy duty hydraulic operated, adjustable bed. ten ton capacity. (Bolts to floor.)

Original factory photograph of 1400 hydra lift

#1400 HYDRA-LIFT

The all new hydraulic motorlift is constructed of heavy duty square tubing, and will lift any size outboard motor to heights of 9feet. The Hydra-Lift will pass through any standard 3'x6'8" door in the low position. Adjustable forks fit all model engines. Abuilt in tilt jack on the rear wheels assures balance and stability. 3½"x12½" tires for use in shop or yard.

SHEET 4
Original factory photograph of 1500 test tank

#1500 BACK UP TEST TANK

This new improved tank is designed for all outdrives as well as outboards on boats. Tank is versatile and functional. Neoprene rubber across the front and a sliding lid protects and adjusts to almost any boat and motor. 3'x10' with 510 gallon water capacity. Double lids and baffles.

The time is now when every minute saved means greater profit,customer satisfaction, and above all pride in Service.

Please contact the manufacturer direct for prices and/or additional information.

BOB KERR'S MARINE TOOL COMPANY
P.O. BOX 1135
WINTER GARDEN, FLORIDA 32787

Your investment today in time and labor saving shop equipment is an investment in economy of operation.

DO NOT CONTACT OUR SERVICE DEPARTMENT SINCE THIS EQUIPMENT IS NOT A PRODUCT OF OUTBOARD MARINE CORPORATION, OMC DISCLAIMS ANY LIABILITY FOR INJURY OR DAMAGES ARISING OUT OF THE USE OR MISUSE THERE OF.

OUTBOARD MARINE CORPORATION HAS NO CONTROL OVER THE MANUFACTURE OR QUALITY CONTROL OF THIS EQUIPMENT OR IT'S CONTENTS AND CANNOT GUARANTEE THAT ALL MENTIONED PRODUCTS IN THE FUTURE WILL PERFORM AS SPECIFIED.

NOTE: POST UNDER HEADING "TIME SAVING AND ORGANIZERS."
JOHNSON OUTBOARDS
Bill Scheske
Manager, Technical Services