Outrigger transom bracket installation safety precautions. December 1984.

Models: All 3-Cylinder and Larger Outboard Models
Shop Information
No. 2077 Rev. 1
Safety Warning December, 1984 Subject: | Use of Outrigger Type Transom Brackets Models: All 3-Cylinder and Larger Outboard Models
There have been some reports of problems when Evinrude® or Johnson® 3, 4, 5, and 8-cylinder model outboards are mounted on outrigger type transom brackets. The existence or severity of the following problem areas will depend on many factors such as engine type, number of outboards, boat transom design, boat bottom design, type of set-up (performance or conservative), weight distribution and type of steering being used.
The dealer becomes the manufacturer when he installs an outboard on a boat. Since the dealer is responsible for the quality and safety of the installation, it is important to understand and eliminate any potential problems before delivery of the equipment to the customer.
ry Problems that can affect the outboard motor, accessory equipment (i.e., steering and controls), and ~ boat occupant safety when using outrigger type transom brackets are:
1. Steering Problems — Steering tie bars or other steering system parts can come in contact with
the outrigger type transom bracket when the outboard is tilted. Damage to steering system parts may contribute to steering system severance or jamming and result in sudden, unexpected loss of boat control. Be sure that there is ample clearance between the outrigger type transom bracket and the outboard steering system parts in all phases of tilting and turning of the outboard.
2. Shift/Throttle Problems — Shift/throttle cables can be damaged if they get pinched between the
outboard and outrigger type transom bracket or boat. Be sure the cables have no less than a 6-inch radius in any position of tilting and turning. Failure of or damage to shift/throttle components may result in sudden, unexpected loss of shift and/or throttle control.
3a. Water Ingestion — When water spray is concentrated near the front of the lower engine cover it can be pulled into the engine through the air intake in the lower engine cover on some models. Water can also enter from a following sea or when backing up.
Note
Severe and immediate engine damage can result from water ingestion.
3b. The design of the outrigger type brackets puts the outboard(s) far behind the transom. When the waterline rises above the exhaust relief holes, water can be ingested into the bottom cylinder from a following sea, during rapid deceleration, when backing the boat, or if the engine stalls on acceleration.
S oO Note: Severe and immediate engine damage can result from water ingestion.
(Continued)
A\ Safety Related CR85-05
Models: All 3-Cylinder and Larger Outboard Models
4. Engine Idle — If the exhaust relief holes are submerged during idle operation, exhaust fumes can enter the carburetor(s) through the air intake in the lower engine cover, causing erratic idling, stalling, and spark plug fouling.
5a. Tilt Limitation — Tilt limitation problems can prevent proper operation of the mechanical trail lock ~@ feature. Make sure the trail lock can be fully engaged to prevent sudden, unexpected dropping of the: outboard which could happen during service or maintenance procedures to the outboard’s hydraulic trim and tilt systems.
5b. Hitting an underwater object will cause the motor to tilt up rapidly. The design and installation
of outrigger type transom brackets may severely limit the ability of the outboard motor to operate through its designed full tilt range. Limiting the outboard’s tilting range also reduces the ability of the shock absorption system to protect the outboard from damage. Make sure the engine cover does not contact the back of the transom during tilting, which could limit the outboard’s tilt range and cause damage to engine cover. Limiting the tilt system could result in damage to outboard mounting parts and result in sudden loss of control. Never restrict the angle through which the motor can tilt.
6. The trim range provided by the hydraulic trim system of an outboard is designed for outboard boats having a transom angle of 14° ± 2°. Many boats designed for stern drive or inboard units have typical transom angles of 0 to 11 degrees. If an outboard is attached to a “converted” inboard or stern drive boat hull, the boat/outboard combination will not perform properly nor be as stable as a properly trimmed-out unit. Make sure the outrigger type transom bracket is mounted to meet the 14° ± 2° transom angle recommended for outboard boats.
7. Many boats, especially those designed for stern drive or inboard installation, do not have adequate transom strength to withstand the loads produced by the thrust and twisting force of an outboard mounted on an outrigger type bracket. The transom must also withstand forces transmitted through the motor when an underwater object is hit. A considerable amount of transom reinforcement may be required to provide adequate strength to withstand these loads. Failure to provide adequate transom strength may result in loss of boat control or the motor dislocating from the boat's transom due to severe underwater impact to the motor’s gearcase. Y
Warranty consideration will not be given if failure is due to incorrect installation on outrigger type outboard transom brackets. Warranty is not voided merely by the installation of the motor on an outrigger type transom bracket.
AN Safety Related