OMC Outboard Service Bulletin No. 2328, June 1998. Powerhead replacement troubleshooting and return procedures. Models: All.
Oiservicemanacen Cl servicewaren (Cl recuwicant Cl recunican2 = (C] tecuwcans rue
ROUTE To:
Powerh
No. 2328
June, 1998
Subject:
Powerhead Replacement Process
Models:
All
Problem:
When an outboard powerhead fails, it is serious for the manufacturer, the dealer, and
most importantly, the customer.
Determining why the powerhead failed and preventing another failure are vital parts of
the powerhead replacement process.
Use these points to help gather information and identify the exact cause of failure.
Solution:
© Question the customer. What were the operating conditions when the failure occurred?
Fast? Slow? Just fueled up? Just out of storage?
© Was outboard properly winterized? Was the fuel treated before storage?
VRO® equipped: Was outboard using excessive oil? Was there a fuel line air leak or
iction in fuel line?
© Verify installation height is correct.
© Verify that the correct spark plugs were used.
® Disassemble and inspect carburetors for debris. Inspect for incorrect or mismatched
parts such as jets or gaskets.
© 2-Cycle: Verify no water or fuel in oil tank, all lines and connections are in good
condition and not pinched.
© FFI™ equipped: Verify that oil hoses are attached to correct powerhead oil lines.
Any indication of overheating? Check for dull powerhead paint, melted wires, or stuck
thermostat.
© Are flywheel magnets secure? Are sensor magnets loose or damaged?
© Are cylinders rusty or brown in color? Check for cold idle, lack of proper storage
procedure, or water ingestion.
© 4-Cycle: Was break-in lubricant changed at 20 hours? Was new filter and OMC Ultra
4Stroke Oil used?
(Continued) cR98-18
© 2-Cycle: Is there excessive carbon on pistons, stuck rings? Was TC-W3® oil used?
© 2-Cycle (Except FF): If only some cylinders are scored, the problem is not oil related.
Check for incorrect spark plugs, timing, water ingestion, carburetor blockage, or excess
carbon.
© FFI equipped: If only some cylinders are scored, test oil system, See OMC Service
Manual - Section 8. Check for incorrect spark plugs, water ingestion, or excess
carbon.
© 2-Cycle: Are the crankshaft bearing surfaces oily or are they dry and discolored? Dry
indicates an oil related failure.
After Installing New Powerhead - Before Returning Outboard to Customer:
© Verify no pinched or leaking fuel or oil lines in boat.
© Perform Linkage Adjustment Procedure, Section 1.
© Mark approximate TDC on flywheel for each cylinder. See OMC Service Manual —
Section 3 — Indexing Flywheel, Erratic Ignition. Put timing light on each cylinder after
indexing - look for erratic igi
© VRO equipped: Follow procedure in the 1998 or newer OMC Service Manual — Section 2
- Initial Testing of VRO Oil System and Oil Warnings.
@ VRO equipped: Perform vacuum test on oil supply hose and pickup.
© FFI equipped: Follow procedure in OMC Service Manual - Section 4 - Action Steps —
Oil System to test and verify operation.
© 2-Cycle: If the failure appeared to be from a lean condition, perform fuel system test
with vacuum gauge and clear hose. See OMC Service Manual — Section 2 - Testing
Fuel System. Look for excessive vacuum and air or fuel vapor bubbles.
© Disassemble and inspect water pump.
© Verify that rig is correctly propped and engine turns correct RPM at WOT with normal
load in boat.
When Returning Outboard to Custom:
© Does customer have the OMC Operator's Manual for his outboard to find correct
information on oil, operating procedures, maintenance, and winterization?
© Inform customer that the powerhead is new. He must follow the break-in procedure
outlined in the operator's manual. Review procedure with customer.
© VRO equipped: Mark oil tank and explain how to verify oil consumption before using
clear fuel.
@ 2-Cycle: Recommend that customer return outboard for inspection and retorquing after
about 20 hours of operation.
© 4-Cycle: Use break-in lubricant for 20 hours. Change filter and oil to OMC Ultra 4-Stroke
Oil.
© Give tags that were attached to powerhead to the customer.