Performance Efficiency Pointers #4 - Maximum Performance Tips

This Johnson Outboards factory publication explains how engine tuning, hull preparation, motor mounting height, and propeller selection affect boat performance. It also includes a 1977 V-6 steering safety warning and a correction to PEP-3.

Johnson Outboards Performance Efficiency Pointers factory letterhead

SUBJECT: MAXIMUM PERFORMANCE TIPS

In answer to the many inquiries about how to obtain the maximum performance from our outboards, we have compiled the following basic suggestions to assist you in preparing a boat and motor combination to utilize all of the performance built into your outboard motor.

ON MODELS:   All Performance Applications

THE MOTOR

We do not recommend any modifications to a motor, other than those which we release to the dealer through Service Bulletins, which are designed to improve the dependability and durability of your motor. Attempts to modify the powerhead, lower unit, ignition system, or carburetors in an attempt to “soup up” a motor will usually result in a loss of performance as well as poor idling and less low speed power. The work on the motor should be confined to making sure that the motor is developing its designed power output. This can be accomplished by first making sure that the motor is in good mechanical condition and that the motor is adjusted as per the tune-up specifications for that motor. The motor should then be test run with the correct test propeller to determine the maximum RPM of the motor with the test prop. If the motor does not reach the RPM specified for the test prop, it will be necessary to locate and correct the cause of the low RPM. If the maximum RPM meets or exceeds the specified RPM, the motor is developing its rated horsepower and the boat and propeller can be examined for further performance gains.

THE BOAT

The area of the boat which most directly affects its performance is the bottom portion of the hull that directly contacts the water when the boat is running. This area of the hull should not only be clean, but should be very straight without any hooks or rockers. To check the straightness of the hull, lay a long straightedge, about 3′ - 5′ long, along the hull at various positions parallel to the centerline of the hull. Before straightening a particular hull, it is advisable to contact the boat manufacturer to determine if the hook or rocker is an integral part of the hull design. Any hooks or rockers that are found, will have to be straightened, as these hull irregularities can cause a loss of boat speed, as well as a tendency for the boat to be unstable (“fishtail”) at high speed or in turns. To straighten the hull, use a long, straight sanding block and a coarse sanding paper. The block should be at least 3′ long. Move block parallel to centerline of hull and check the surface periodically with the straightedge. In some cases, it may become necessary to fill some of the low areas to prevent excessive sanding. At this time, also sharpen all edges and corners on the running areas of the hull, including the strakes and chines and the bottom edge of the transom. Once the hull is straight and the edges sharpened, finish sand the worked area with #400 grit sandpaper until super smooth. Paint the worked area with automotive black lacquer primer, wet sanding after the final coat with #600 grit sandpaper. Do not wax! This entire process is known as “blueprinting” the hull.

MOUNTING THE MOTOR AND SELECTING A PROPELLER

As a starting point, the motor should be mounted so that the lower anti-cavitation plate is level with the bottom of the hull. Select a propeller, preferably an SST of the size recommended in the propeller chart of the OMC Accessory Catalog. The SST propeller will allow the motor to run higher on the transom, without ventilation, than an aluminum propeller and can give from 1-5 mph more speed than an aluminum propeller. Remember that the higher the motor can run on the transom, without ventilation, the less lower unit there is dragging in the water and the higher the potential top speed. While racing propellers can run as much as 5″ higher than an SST, the racing propellers are not suitable for normal pleasure boating and will offer little speed increases on a pleasure hull. They are designed only for racing applications with extremely light deep-V hulls or tunnel hulls and do not have a rubber clutch to protect a motor for normal usage.

Once the SST propeller is installed, test run the boat to determine the maximum RPM at wide open throttle. When making this test, vary the motor angle, using either a power trim unit or by varying the tilt pin position to determine what trim angle gives the maximum RPM and boat speed. If the RPM is 300-400 RPM below the maximum recommended RPM for the motor, try the next lower pitch of SST propeller to increase the RPM to as near the recommended maximum as possible. If the RPM is 300-400 over the maximum recommended RPM, try the next higher pitch of SST propeller to decrease the engine RPM to within the recommended maximum. For example, the recommended maximum RPM for a 1977 115 HP outboard is 5500 and it should be propped so that it operates within the 5300-5500 RPM range.

Repeat the test after raising the motor one set of adjustment holes up on the transom. If the RPM increases beyond the maximum RPM range of the motor, due to the lower drag encountered when the motor is raised on the transom, go to the next higher pitch SST propeller. Continue raising the motor and re-testing until a height is reached where the amount of ventilation or slippage is unacceptable, then lower the motor one set of holes. Excessive ventilation can also be lessened by adding additional cupping to the SST propeller as outlined in the Bulletin on “140 H.P. motors on Bass Boats”. This should give the optimum motor height as well as the optimum propeller size. When the combination of optimum motor height, motor angle, and the correct propeller is put together, the boat and motor will be operating at the maximum efficiency and speed.

Safety warning triangleSAFETY WARNING:  (Quote from 1977 Operators Manual)

Our V-6 outboards are high powered motors designed to give stable boat performance on most boats with appropriate horsepower ratings. The degree of stability will vary with different boat-propeller-motor combinations. If your boat has a tendency to be unstable (“fishtail”) at high speed or in turns, it may require optional motion mounts and/or twin cable steering. See your dealer for the necessary mounts and/or steering kits to correct this condition, if it exists for your combination of boat-propeller-motor.

Twin cable steering must be used when dual V-6 motors are installed. We recommend twin cable systems for dual motors of 150 H.P. or over.

Combine a properly tuned motor, a boat with a blueprinted hull, and some careful attention to the motor installation and propeller selection, and the results will be a boat/motor combination that not only out-performs identical but less carefully prepared outfits, but one that gives increased fuel efficiency as well.

CORRECTION

On P.E.P. - #3, Figure 2, V-4 standard mount number
is 387783, please make correction.

Tools, supplies and related parts

Suggested products related to this service bulletin. Verify fit and suitability before ordering.

Amazon: tools and supplies

Marine Propeller Hub Kit & Prop Nut Wrench

Search for these supplies on Amazon

eBay: OMC / Evinrude OEM part 387783

Search for original or compatible replacement part 387783. Check the bulletin for supersessions and model fit.

Click here to search on eBay

Affiliate disclosure: EverythingOutboards may earn a commission from qualifying purchases. As an Amazon Associate, we earn from qualifying purchases.