Johnson Service Bulletin SB-1024 - Slow-Speed Needle Adjustment

June 30, 1964. Supplementary adjustment procedure for Johnson 90 HP four-barrel carburetors, with factory float-height illustration and reference to SB-989A.

Johnson Motors gray service bulletin header
SB-1024
June 30, 1964
SUBJECT: SUPPLEMENTARY SLOW-SPEED NEEDLE ADJUSTING PROCEDURE FOR 90 HP FOUR-BARREL CARBURETORS.
Reports from the field indicate that an occasional hesitation on fast acceleration or a flat spot at approximately 2400 - 2800 rpm will occur on 90 HP engines. These two conditions have been noted to exist even after the slow-speed needles were adjusted in accordance with Service Bulletin #SB-989A.
The following procedure is now recommended for eliminating the trouble- some hesitancy and flat spot whenever these conditions cannot be cor- rected by the procedure outlined in #SB-989A. Proceed as follows:
Step #1 - Before starting engine, move bar controlling slow-speed needle knobs to its lowest (or leanest) position. Remove all four nylon knobs.
Step #2 - Set each slow-speed needle 3/4 turn open.
Step #3 - Start engine and run at fast idle until normal operating tem- perature is reached. Then shift into forward gear (using test wheel or running with propeller) and set engine speed at exactly 1500 rpm by tachometer reading. (RPM must be set precisely with a tachometer and not by ear)
Step #4 - With engine running at 1500 rpm, adjust top needle until highest rpm reading is achieved. Perform same adjustment to needles 2, 3 and 4. Do not favor rich or lean but peak each needle for highest rpm reading on tachometer. When finished, tachometer should read approximately 2000 to 2200 rpm.
Step #5 - Speed engine up to about 3500 to 4000 rpm to clear crankcase and cylinders. Again, bring engine to 1500 rpm (in gear) and repeat Step #4 as many times as is necessary to attain highest possible rpm on the tachometer.
Step #6 - Be sure adjustment bar is in the extreme down (or lean) po- sition. Install all nylon knobs with bar in this position. Raise the bar until all knobs are horizontal or straight across. This will richen all needles approximately 1/8 turn.
Step #7 - Adjust engine idle to 650 rpm by turning idle screw at top of carburetor (with engine in gear) as the final step.
- OVER -
PAGE 2 SERVICE BULLETIN SB-1024
JOHNSON MOTORS, DIVISION OF OUTBOARD MARINE CORPORATION, WAUKEGAN, ILLINOIS 60086
It should also be remembered that other conditions can contribute to the problems just mentioned, and that no amount of slow-speed needle adjustment will improve performance when such problems exist. Improper float settings should be considered as possible causes of flat spots, as should clogged orifice plugs (fixed high-speed jets) and idle/in- termediate speed fuel restrictors. Carburetor fuel passages can be cleaned with compressed air. Each of the four floats can be checked and re-set as follows: (Setting for all four floats is identical)
With the float chamber inverted as shown in Fig. 1, establish a point (A) on the edge of the float that is 5/16" from the inner edge of the float well at point (B). Draw a light pencil mark on the float at point (A). Float height should measure 9/16" between point (A) on the edge of float and point (C) on inner top edge of float well if setting is correct. Re- move float and carefully bend tang towards float if the dimen- sion between points (B) and (C) is less than 9/16"; bend tang away from float if dimension is more than 9/16". Float must be adjusted (by bending tangs) until correct setting is achieved.
Figure 1 original Johnson carburetor float measurement illustration with points A B and C
Figure 1
Sincerely, JOHNSON MOTORS Robert Compton Administrative Assistant
RC/lfl
NOTE: Post on VM-90 Index under heading "CARBURETOR".

Related bulletin

This bulletin supplements SB-989A, which describes the earlier slow-speed needle adjustment procedure.